现在时间是:
搜索

会员登陆

当前位置:首 页 >> 数控冲床工艺>> 数控冲床工艺>> 文章列表

台励福数控冲床报警代码说明

作者:佚名   发布时间:2013-06-06 20:50:41   浏览次数:36831

 

1000        T ZRN UNCOMPLETED! T軸歸零未完成

1001        RAM ISN'T AT TOP DEAD POINT. 沖頭不在上死點

1002        TOOL ISN'T AT UPPER HOME POSITION. 刀具不在上死點

1003        SHOT PINS CAN NOT IN/OUT TURRET. 刀盤插梢不能插入或退出。

1004        SAFETY ZONE DETECTOR ARE BROKEN. X方向安全區偵測器斷線。

1005        PRESS MOTOR CONVER/SW. ON PANEL. 飛輪蓋未關。

1006        X/Y ZRN FIRST! X/Y軸請先執行歸零。

1007        R.A.M ISN'T AT FIXED POINT. 沖頭未停於內或外圈。

1008        INSULATOR OF THE PUNCH HEAD沖頭上死點偵測器,絕緣部份損壞。

1009        MODE SELECTOR CHANGED! 模式變更

1010        AIR PRESSURE LOW空壓過低 

1011        OIL PRESSURE LOW油壓過低 

1012        CLUTCH WARM UP!機台暖機中(CP機種)

1013        CLUTCH VALVE IS CLOGGED OR FAILED.沖壓電磁閥阻塞失敗(CP機種)

1014        PLC BATTERY LOW PLC電力不足,請更換電池。 

1015        PLC NO RESPONSE PLC無回應,PLC線路有問題。 

1016        WAITING 2ND. SENT FROM PLC 等待從PLC寄出之第二訊息

1017        PFIN SIGNAL ERROR 沖壓訊號未結束 

1018        NFIN SIGNAL ERROR 蠶食訊號未結束

1020        TURRET TYPE SETTING ERROR刀盤型式設定錯誤 

1021        OVER PUNCH 沖壓頓數超過機器可沖壓頓數之設定值

1022        THE C'SHAFT CANN'T IN OR OUT. C軸插梢不能插入或退出

1023        TOOL NUMBER SETTING ERROR. 刀站數設定有疑問

1024        A WRONG MACHINE SERIES NUMBER SETTING 機器系列號碼錯誤                                  

1025        SECURITY CODE TEST KEY IS ON. 安全保護測試開啟                                  

1030        HS1 HAS NO RESPONSE.(MODE SETTING ERROR, MODE=2) HS1無回應。

1031        HS1 MODE RESP.ERROR.MODE=[I120,R59](MODE SETTING IS NOT EQUAL TO 2)HS1模式回應錯誤                                  

1050        HYDRAULIC UNIT油壓控制。 

1051        HYDRAULIC SYSTEM SELECTION油壓系統選擇.                                  

1052        HNC100 ALARM X1003 HNC 100 警訊 X1003                                  

1053        FILTER IS CLOGGED!油過濾器阻塞   X10092.5 ->20    X1004.3->10                                  

1054        OIL LEVEL IS LOWER油壓液面低                                  

1055        FLUSHING MODE SETTING油洗模式設定                                  

1056        HNC100 CONNECTING CHECK HE302 連結檢查                                  

1057        SHEAR TOOL滾刀模式                                  

1058        PF ISSUED BUT NOT RESPONDANCE. 沖壓訊號出現但機台無相關回應                                  

1059        HYDRAULIC MOTOR SW. 油壓馬達開關                                  

1060        C LOCK/RELEASE DRIVER.C軸鎖定/釋放訊號錯誤

1061        T0OL NOT IN AGREEMENT刀具不一致(M碼設定與控制器內設定不符) 

2000        TO PERFORM THE C AXIS ZRN. RETURN FIRST! 請先執行C軸歸零。                                  

2001        THE TOOL LIFT SWITCH BE PLACED AT ON POSITION. 取刀具開關置於"開"的位置。                                   

2002        THE SWITCH OF THE TURRET PIN BE PLACED AT OUT POSITION刀盤插梢的進/出 開關置於"出"的位置 

2003        THE LUBRICATING SYSTEM OF X/Y AXIS MOVING PARTS FAILS.X/Y軸移動部潤滑系統失效

2004        PLEASE CONTACT TAILIFT FOR THE PERIODICAL MAINTENANCE.周期性之保養提醒

2005        BROKEN LINE IN TRIANGLE POSITIONING DETECTS.(ON-LINE EFFECTIVE) 三角定位偵測器斷線。(ON-Line有效)。(使用於自動送料系統)。                                     

2006        THE OIL COOLING SYSTEM FAILS. 油溫冷卻系統失效。

2007        THE CLAW IS OPEN. 夾爪打開

2008         INTRUDING THE CLAW INTO THE REPOSITION SAFETY ZONE.PLEASE RESET THE MESSAGE FIRST 夾爪進入換爪安全區請按RESET消除警訊

2020        TOOL CHANGE DOOR OPEN. 換刀門開啟。

2021        OIL TEMPERATURE TOO HIGH. 油溫過高。 

2022        THE X GAUGE BLOCK POPS UP. 原點定位塊上升 

2023        THE WORKBENCH OPEN. 換刀位置桌面開啓

2024        THE WORK TABLE'S BALLS HAVE RISEN. 檯珠上升 

2025        SAFETY GUARD IS INTERRUPT. 光柵被遮斷 

2026        THE TOOL CHANGE SWITCH IS AT ON POSITION.換刀位置開關置於開(ON)的位置

2027        TOOL LIFE EXPIRED. 刀具壽命周期到達 

2028        WORKPIECE CURVED. 板件彎曲 

2029        WORKPIECE SHIFTED. 板件偏移 

2030        TOOL LUBRICANT IS EMPTY. 無刀具潤滑油 

2031        THE TOOL CHANGE CONFIRMATION SWITCH. 暖機開關

2032        WAITING THE RISE OF OIL PRESSURE. 等待油壓上升 

2033        THE H+L SYSTEM IS NOT READY. H+L系統沒準備好 

2034        THE RESET BUTTON ON PANEL FOR EXTERNAL ALARM IS CLOSED. 外部面板上面的reset按鈕警訊關閉 

2035        PERFORM ZRN FOR ALL AXES. 完成四軸歸零 

2036        WARM UP FINISHED! 暖機完成 

2037        Y AXIS MACHINE LOCK機器上Y軸鎖定                                                        

2038        PERFORM ALL AXES REFERENCE POSITION RETURN FIRSTLY. 四軸先歸零

2039        PLEASE INPUT PASSWORD! TERMS=   輸入密碼TERMS=

2040        PLEASE INPUT THE T & M CODE OR CHECK THE CODE CONTENTS FIRSTLY.先輸入自己所需的T、M碼

2041        SHEAR MODE WITH WILSON WHEEL TOOL 在轉刀工位使用滾筋模具與模式加工但程式M碼誤設定為PUNCH模式

2042        WORKBENCH'S UPPER/LOWER DETECTOR.工作檯未定位

2043        WORKBENCH HOLDER DETECTORS.工作檯定位有問題









请填写详细信息发表评论
评论名字:
电子邮件:
评论内容:
验证字码: 验证码

Copyright ©2018    钣金技术资源网 All Right Reserved.

Powered by LingCms 版权所有 © 2005-2018 Lingd.Net..

点击这里给我发消息广东省深圳市龙华新区大浪街道谭罗路39号